Full Overlay vs Half Overlay vs Inset Soft-Close Hinges
Oct 20, 2026
Images are illustrative renderings.
Concealed cabinet hinges look almost identical in the box. The difference is the arm, and the arm decides where the door sits on the cabinet. Order the wrong one and the door hits its neighbor, leaves a gap, or will not close. This guide explains the three overlays in plain terms and how to pick one for RV, marine and cabinet builds.
What "overlay" means
Overlay is how much of the cabinet's side panel (or face frame) the door covers when it is closed.
- Full overlay: the door covers the side panel completely.
- Half overlay: two doors share one center partition, each covering half of it.
- Inset: the door sits flush inside the cabinet opening and covers nothing.
All three of our soft-close hinges, CT-HSC-F, CT-HSC-H and CT-HSC-I, share the same platform. Each has hydraulic soft-close, clip-on mounting, a 3D cam adjustment of ±2 mm, copper + nickel dual-layer plating and a 4-hole mounting plate. Only the overlay changes.
Full overlay (CT-HSC-F)
Pick it when: the door is on the end of a run, or on a single cabinet, and should cover the whole side panel.
This is the modern frameless look: doors edge to edge with small, even reveals. In an RV it suits single overhead lockers, the end door of a galley run and bath cabinets. In a kitchen it is the default for uppers, lowers and tall pantry doors.
Shop the CT-HSC-F full overlay hinge
Half overlay (CT-HSC-H)
Pick it when: two doors hang off the same center partition.
If you put full overlay hinges on both doors sharing a partition, the doors try to cover the same strip of panel and collide. A half overlay arm sets each door back so both close cleanly with an even gap. Classic uses are a bath vanity with a pair of doors on one center divider, double overhead lockers in an RV, and side-by-side galley cabinets on a boat.
Shop the CT-HSC-H half overlay hinge
Inset (CT-HSC-I)
Pick it when: the door should sit flush inside the frame, face even with the cabinet front.
Inset is the furniture look. It is also handy in tight RV and boat interiors where a door that sits proud would catch on a passing hip or a seat cushion. Inset doors need accurate openings, because the reveal shows all the way around. The 3D cam adjustment is what makes that reveal even after hanging.
A quick way to decide
Close the door (or picture it closed) and look at the side panel next to the hinge:
- Is the panel fully hidden behind this door? Full overlay.
- Is the panel shared with another door that hinges off it? Half overlay.
- Is the door inside the opening, flush with the front? Inset.
Mixed cabinets are normal. A galley run might use full overlay on the end doors and half overlay on the pair in the middle. Order by door position, not by cabinet.
Why soft-close matters in RVs and boats
Doors in a rolling or rocking interior get opened all day and slammed by accident. The hydraulic soft-close built into the CT-HSC hinges damps the last part of the swing and pulls the door shut quietly, with no add-on dampers or bumpers. The catalog lists RV galley and bath lockers and boat cabin interiors as intended uses.
One limit: the copper + nickel plating is meant for interior cabinetry. Do not use these hinges on exterior compartments or deck lockers that see weather.
Clip-on mounting saves service time
The hinge arm snaps onto its mounting plate by hand and comes off with the release button, with a steel clip and button rather than plastic. That matters in an RV or boat, where doors come off for access to plumbing, wiring and tanks. Pop the door, do the job and clip it back on without losing your adjustment.
Hanging and adjusting
- Set the hinge cup in the door and fix the 4-hole plate to the side panel.
- Clip the arm onto the plate.
- Use the 3D cam to dial the door: height (up and down), depth (in and out) and side (the reveal to the next door), each ±2 mm.
- Tall doors need more hinges. The catalog shows a tall wardrobe door hung on four.
Before you bore doors, email cs@conversionstech.com for the full specification sheet: cup dimensions, opening angle, door thickness range and plate height options.
FAQ
What is the difference between full overlay and half overlay hinges?
A full overlay door covers the whole side panel. Half overlay is for two doors that share one center partition, so each covers half of it and they do not collide.
When should I use inset hinges?
Use inset when the door sits flush inside the cabinet frame. It suits furniture-style cabinets and tight RV or boat interiors where a proud door would get in the way.
Can I mix overlay types in one cabinet run?
Yes. Choose by door position. End doors are often full overlay and paired doors on a shared partition are half overlay.
Are these hinges suitable for RVs and boats?
Yes, for interior cabinetry such as RV galley and bath lockers and boat cabin interiors. They are not meant for exterior or weather-exposed doors.
Order hinges or get a quote
Each hinge is $4.95 online, with same-day shipping on in-stock items: full overlay, half overlay and inset. Building a run of RVs, boats or cabinets? Send your BOM with part number, overlay and quantity to cs@conversionstech.com and we will reply within 48 hours with pricing and lead time.