Skip to content
M6 ball socket and ball stud gas spring fittings M6 ball socket and ball stud gas spring fittings

Gas Spring End Fittings Explained: Ball Socket, Ball Stud and M6

Images are illustrative renderings.

The spring gets the attention, but the end fittings decide whether it lasts. A fitting that binds or works loose puts side load on the rod, and side load is what kills a gas spring early. Here is how ball socket and ball stud fittings work, how to install them, and the safety rules from our CT-29 catalog.

The parts of a gas spring connection

Every gas spring has two ends: the cylinder end and the rod end. On our standard CT-GS springs, both ends have an M6 thread. You screw an end fitting onto each one, then attach the fittings to the lid and the cabinet or frame.

The CT-29 catalog lists seven interchangeable end fittings:

Code End fitting
CT-P1 Ball-stud cap
CT-B1 Angled ball-socket bracket
CT-B2 Threaded ball stud
CT-E2 Eyelet, compact
CT-E3 Eyelet, oval
CT-E4 Clevis / fork
CT-E5 Eyelet, heavy

You can mix any two fittings on one spring. For lids and hatches, the ball socket and ball stud pair is the usual choice. Eyelets and clevis forks are for machinery, where the spring rides on a pin.

How a ball socket and ball stud work

Think of a tiny trailer hitch. The ball stud is fixed to the lid or frame. The ball socket snaps over the ball and can swivel in any direction.

That swivel is the point. As the lid opens, the angle between the spring and the lid keeps changing. A ball joint lets the spring follow that change without bending, so the rod is always pushed straight along its axis. The catalog's rule is to allow free articulation at both fittings.

Our CT-B1 / CT-B2 ball socket and ball stud fittings fit the M6 thread on our standard springs:

  • CT-B1, angled ball-socket bracket: $2.95
  • CT-B2, threaded ball stud: $1.95

The socket presses onto the stud by hand, with no hammer or pliers.

Which springs they fit

The CT-B1 and CT-B2 are sold separately for the M6 springs in our standard program:

For the 10 in pair and 12 in pair, check the end fittings shown on the product page before ordering extra hardware, or email us and we will confirm.

Installing ball stud fittings

  1. Plan the mount points. Use the sizing method in how to size a gas spring for a lid or hatch. Check that the spring fits between the points both extended and compressed.
  2. Mount rod down. With the lid closed, the rod should point down. This keeps the seal lubricated.
  3. Fix the ball studs. Screw threaded fittings on completely. Where there is vibration, as in vehicles, boats and machines, make sure they are fully seated and secured.
  4. Line the studs up. The two studs on each spring should sit so the spring runs in a straight line between them, not twisted across the lid.
  5. Press the sockets on by hand.
  6. Cycle the lid slowly. Both ends should swivel freely through the whole swing, with no binding at full open or full closed.

Safety rules from the CT-29 catalog

These are the rules we print in the catalog. Every installer should know them.

A gas spring is not a safety component. Where failure would risk health or life, add an independent locking mechanism. That is the installer's or customer's responsibility.

Mounting

  • Avoid side loading and non-axial forces. Long strokes may need extra support to prevent bending.
  • Allow enough movement in the end fittings.
  • Do not extend or compress beyond the design stroke. Do not use the spring as a dead stop.

Handling

  • Protect the rod from impacts, welding or electrical arcing, grinding sparks, paint and corrosive products.
  • Do not grip the rod with pliers or a vise without protective jaws.
  • Keep the rod clean during installation. The seal runs on it, and minor damage, corrosion or paint on the rod can cause rapid failure.

Storage

  • Up to three months: store horizontally at room temperature.
  • Longer, or in hot climates: store vertically, rod down.
  • Check force and travel on stored stock before installing.

Service life

Gas springs are wear parts. Replace them according to how hard they work and the environment they are in.

FAQ

What thread do your gas spring end fittings use?

Our standard CT-GS gas springs have M6 threads at both ends, and the CT-B1 and CT-B2 fittings fit that M6 thread.

What is the difference between a ball socket and a ball stud?

The ball stud is fixed to the lid or frame. The ball socket on the spring snaps over it and swivels, so the spring can follow the lid's changing angle without side load.

Can I use different fittings on each end?

Yes. Any two of the seven CT-29 end fittings can be mixed on one spring. Specify the left and right codes when you order.

Is a gas spring enough to hold a heavy lid safely?

No. A gas spring is not a safety component. Where a falling lid could hurt someone, add an independent stay or lock.

Order fittings or get a quote

Order CT-B1 and CT-B2 fittings and springs online from the Gas Springs & Fittings collection, with same-day shipping on in-stock items. Need eyelets, clevis forks, brackets or mixed fittings for a production run? Send your BOM to cs@conversionstech.com for a quote within 48 hours.

Back to top