Skip to content
RV storage bay door held open by gas struts RV storage bay door held open by gas struts

RV and Boat Hatch Gas Strut Replacement: Measure, Choose, Install

Images are illustrative renderings.

A storage bay door that will not stay up, or a deck hatch that drops on your head, almost always means a worn gas strut. Gas springs are wear parts. The seals slowly let nitrogen out, and heat, UV, salt and grit speed that up. The good news is that replacement is a 15-minute job once you have the right part.

Step 1: Confirm the strut is the problem

Lift the lid halfway and let go. If it sinks, or only stays up at the very top, the struts have lost force. Also check:

  • Oil or grime on the rod. A leaking seal often leaves a wet film.
  • Bent rod or dented tube. Replace the strut. Do not straighten it.
  • Loose or broken end fittings. Sometimes the strut is fine and only the ball stud or bracket has failed.

Replace struts in pairs. If one has faded, the other is close behind, and a mismatched pair twists the lid.

Step 2: Measure the old strut

Take the strut off before you measure. With the lid propped open securely, pry the ball socket clip back slightly and pull the socket straight off the ball stud.

Measure these with the strut fully extended:

  1. Extended length. Center of one end fitting to center of the other.
  2. Stroke. How far the rod travels from fully extended to fully compressed. If you cannot compress it, measure the exposed rod length as a close guide.
  3. Tube and rod diameter. Calipers help here.
  4. End fittings and thread. Ball socket, eyelet or clevis, and the thread size where the fitting screws on.
  5. Force rating. Many struts have a number in Newtons stamped or printed on the tube, such as 200N. Read it before you throw the old one out.

If the force label is gone, work it out from the lid's weight and geometry. Our guide on how to size a gas spring for a lid or hatch has the formula and examples.

Step 3: Choose the replacement

Match length first, then force, then fittings.

Length. The new strut must fit between the existing mounts both extended and compressed. Compressed length is roughly extended length minus stroke. Too long and the lid will not close. Too short and it will not open fully or the strut will bottom out.

Force. Match the old rating if the lid has not changed. If you have added a heavier panel, insulation or a latch, round up.

What we stock for RV and marine hatches:

The CT-GS15 and CT-GS18 have M6 threads at both ends. Pair them with CT-B1 ball sockets and CT-B2 ball studs if your old studs are worn or a different thread.

On the water. Our standard springs are MS (mild steel). Stainless is available on request for the CT-GS range, so ask before you order if the hatch sees salt spray every day.

Step 4: Install it rod down

  1. Prop the lid. Use a stick or a helper. Never rely on the old strut while you work.
  2. Fit the ball studs if you are replacing them. Screw them all the way in. Our catalog notes that threaded fittings should be fully seated, especially where there is vibration, which describes every RV and boat.
  3. Orient the strut rod down. With the lid closed, the rod should point down and the cylinder up. That keeps the internal oil on the seal, which is what keeps the seal alive.
  4. Press the sockets on. Ball sockets press onto the stud by hand. No hammer or pliers.
  5. Check free movement. Open and close the lid slowly. Both ends should pivot freely with no binding at the top or bottom of travel.

Do not do these

Most early strut failures come from the install, not the strut:

  • Do not grip the rod with pliers or a vise. A single scratch ruins the seal.
  • Do not paint the rod or let overspray, sealant or grinding sparks reach it.
  • Do not side load it. A strut on only one side of a wide hatch twists, and a twisted rod wears out the seal.
  • Do not use the strut as a stop. If the lid swings past the strut's full extension, add a stay or a stop.
  • Do not over-extend or over-compress beyond the stroke.

Storing spares

Keeping a spare pair on board or in the rig is smart. For up to three months, store them lying flat at room temperature. For longer, or in a hot climate, store them standing up, rod down, so the seal stays lubricated. Check force and travel before you fit a spare that has been sitting.

Safety

A gas spring is not a safety component. On a deck hatch or a heavy bay door, where a falling lid could injure someone, add a mechanical stay or lock as well.

FAQ

Which way up does an RV gas strut go?

Rod down with the lid closed, cylinder up. That keeps oil on the seal and makes the strut last longer.

How do I measure a gas strut for replacement?

Measure it fully extended from the center of one end fitting to the other, then measure stroke, tube and rod diameter, end fittings and the force printed on the tube.

Should I replace both hatch struts at once?

Yes. Replace them as a pair so both sides lift evenly. Our 10 in and 12 in springs ship two per box for this reason.

Can I use these gas springs on a boat?

Yes for hatches and lockers. For constant salt exposure, ask about stainless versions of the CT-GS range, and add a stay where a falling hatch could hurt someone.

Order replacements

Order the pair you need online from the Gas Springs & Fittings collection, with same-day shipping on in-stock items. Outfitting a fleet or a production line of RVs or boats? Send your BOM or the old strut's measurements to cs@conversionstech.com for a volume quote.

Back to top