MC4 Extension Cable Length Guide: 10 AWG vs 12 AWG and Voltage Drop
Nov 18, 2026
An MC4 extension cable is the simplest part on a solar job and the one most often bought wrong. Too short and the crew splices in the field. Too long and the slack ends up coiled under the array where it cooks. Wrong gauge and the string loses power every hour of sun for 25 years. This guide covers how long an MC4 extension cable can run, 10 AWG versus 12 AWG, voltage drop numbers you can hand to an inspector, and why a cable cut to the foot beats a stock length.
What an MC4 extension cable is
A length of UL 4703 PV wire with a male MC4 on one end and a female MC4 on the other. It plugs between a module lead and the next module, a combiner, a rapid shutdown device or an inverter input. Conversions Tech builds them on bare copper PV wire, 1500 V DC, in 10 AWG from 5 to 200 ft and 12 AWG from 5 to 100 ft, red or black, cut and assembled to order in Oxnard, CA.
10 AWG or 12 AWG
Both gauges are rated for MC4 connectors, which are 30 A devices. The difference is resistance and ampacity.
| Gauge | Resistance, ohms per 1000 ft, copper at 20C | Ampacity, 90C column (NEC Table 310.16) | Max string Isc after 1.56 factor | Use |
|---|---|---|---|---|
| 12 AWG | 1.59 | 30 A | About 19 A before derating | Module jumpers, microinverter and optimizer leads, short runs under 50 ft |
| 10 AWG | 1.00 | 40 A | About 25 A before derating | String home runs, long jumpers, anything over 50 ft, high current modules |
NEC 690.8 sizes PV conductors at 125 percent of Isc, then 125 percent again for continuous duty, so a module with 13 A Isc needs a conductor good for 20 A after temperature derating. On a hot roof that pushes 12 AWG to its limit. 10 AWG is the default for anything that leaves the module row.
Voltage drop by length
Voltage drop on a jumper is current times resistance times conductor length, counting both the positive and negative legs. The table assumes a 10 A string at 400 V DC and copper at 20C. NEC Chapter 9 Table 8 lists 1.98 (12 AWG) and 1.24 (10 AWG) ohms per 1000 ft for stranded uncoated copper at 75C, so hot conductors run about 25 percent higher than this table.
| Extension length | Conductor in circuit | 12 AWG drop | 12 AWG percent | 10 AWG drop | 10 AWG percent |
|---|---|---|---|---|---|
| 25 ft | 50 ft | 0.8 V | 0.2 percent | 0.5 V | 0.13 percent |
| 50 ft | 100 ft | 1.6 V | 0.4 percent | 1.0 V | 0.25 percent |
| 100 ft | 200 ft | 3.2 V | 0.8 percent | 2.0 V | 0.5 percent |
| 200 ft | 400 ft | 6.4 V | 1.6 percent | 4.0 V | 1.0 percent |
Most designers hold total DC voltage drop under 2 percent and many spec 1 percent. At 400 V string voltage 10 AWG stays under 1 percent out to 200 ft. At lower string voltages, a 12 module residential string around 450 V is fine, but a 48 V battery charge circuit is not, and 12 AWG runs over 25 ft start costing real energy. Run the numbers at your string voltage, not the nominal.
How long is too long
There is no code maximum length for an MC4 extension. The limits are voltage drop, the 30 A connector rating, and the rule that PV wire exposed outdoors must be sunlight resistant and supported. Practical limits:
- Module to module jumpers: 3 to 10 ft, 12 AWG is fine.
- Row to row and across a roof: 10 to 50 ft, 10 AWG.
- Array to combiner or inverter: 25 to 250 ft, 10 AWG, usually as a home run with a stripped end instead of a second MC4.
- Ground mount to house: run in conduit as THWN-2, not as an MC4 extension, past the first disconnect.
Why cut to length beats stock lengths
Stock extensions come in 10, 15, 25 and 50 ft. A 38 ft run gets a 50 ft cable and 12 ft of slack. That slack is coiled under a module, where it sits in heat and chafes on the rail. On a 40 module array that is a few hundred feet of wire you paid for and now have to secure. A cable cut to the foot costs less per job, installs faster and leaves nothing to bundle. The 10 AWG custom MC4 jumper and 12 AWG custom MC4 jumper price every length from 5 ft up online.
Connector compatibility
NEC 690.33(C) requires mating connectors to be from the same manufacturer or listed as intermateable. Conversions Tech MC4 is the default on our cables, and the other connector options are listed on each custom cable page so the extension matches the module leads. Order one brand per assembly and match it to the modules on site. Details are in our connector brand guide.
Ordering
Pick gauge, length, color and connector brand on the custom solar jumper page or build a full cut list in the Custom Cable Builder, which also prices MC4 to bare wire leads and home run cables from 25 to 250 ft. Browse all solar panel extension cables. Hydraulic crimped, pull tested, labeled per string on request, cut and assembled to order in Oxnard, CA. Trade accounts get net terms. cs@conversionstech.com or 1 (307) 206-0534.
FAQ
How long can an MC4 extension cable be?
No code maximum. Hold voltage drop under 1 to 2 percent at your string voltage. With 10 AWG on a 400 V string that allows about 200 ft.
Is 12 AWG enough for solar extension cable?
For short module jumpers and microinverter leads, yes. For runs over 50 ft or modules above about 12 A Isc, use 10 AWG.
Can I join two MC4 extension cables?
Yes, male to female, as long as both are the same connector brand or listed intermateable. Fewer connections is better. Order the length you need.
Can MC4 extension cable be buried or run in conduit?
PV wire is listed for exposed outdoor use and can be run in conduit. For direct burial use USE-2 or run PV wire in conduit. Follow NEC 690.31.